Manuale Lokprogrammer 4.4.13

[Gianfranco Lo Coco]

Ciao a tutti allego il link da cui poter scaricare il manuale del Lokprogrammer in inglese in versione 4.4.13 .

http://www.mediafire.com/view/sutvo98qr ... _eBook.pdf

[Frecciarossa]

Grazie Gianfranco! Stasera dopo mooolto tempo ho riacceso il Lok Programmer e ho visto che c'è l'aggiornamento alla versione 4.5.1; che tu sappia rispetto alla versione 4.4.13 ci sono state delle implementazioni di rilievo? Grazie!

[Gianfranco Lo Coco]

Ecco la risposta



Microsoft .NET Framework 3.5 SP1 is required. The .NET Framework will be installed automatically if the computer is connected to the internet.
Supported decoders
LokSound
LokSound V4.0
LokSound V4.0 M4
LokSound V4.0 M4 OEM
LokSound micro V4.0
LokSound XL V4.0
LokSound L V4.0
LokSound Select
LokSound Select direct / micro
LokSound Select OEM
LokSound Select L
LokSound V3.5
LokSound XL V3.5
LokSound V3.0 M4
LokSound micro V3.5
LokPilot
LokPilot V4.0
LokPilot V4.0 DCC
LokPilot V4.0 PX
LokPilot V4.0 M4
LokPilot micro V4.0
LokPilot micro V4.0 DCC
LokPilot XL V4.0
LokPilot Fx V4.0
LokPilot Standard V1.0
LokPilot Nano Standard V1.0
LokPilot Fx Nano V1.0
LokPilot V3.0
LokPilot V3.0 DCC
LokPilot V3.0 M4
LokPilot V3.0 OEM
LokPilot micro V3.0
LokPilot micro V3.0 DCC
LokPilot XL V3.0
LokPilot Fx V3.0
LokPilot Fx micro V3.0
LokPilot Basic
LokPilot Basic (LA)
SwitchPilot
SwitchPilot
SwitchPilot Servo
SwitchPilot Servo (MA)
SwitchPilot Servo (2013)
SwitchPilot V2.0
SwitchPilot Servo V2.0
Sonstige
Test coach EHG388
Smoke Unit (Gauge 0, G)
KM1 Smoke Unit
ESU digital interior light
4.5.1
Output mode Roco coupler was missing on LokPilot V4.0 DCC.
Firmware Version 1.2.1405 for LokPilot Standard Nano and LokPilot Standard Nano Fx.
4.5.0 
Virtual command station uses momentary function settings from the current project.
Added sound selection CV to sound slot settings.
Fixed sound slot previrew for LokSound Select.
Added snap to grid function to sound schedule editor.
Added comments to sound schedule editor.
Start- and end state size is now changable.
Paste in sound schedule is now aware of the current scroll position.
Added flash size to extended decoder information.
Could not open .esux files of non-updateable decoders.
LokSound Firmware 4.15.9240: Added Heavy Load and Coast mode.
4.4.24
Improved sound slot and phyisical output configuration user interface.
Display function icons of the current project to virtual command station.
Highlight current state in sound slot simulator.
Fixed problems with "changed" state.
Improved compatibility with LokSound XL V3.5 (Piko version)
New Firmware for ScaleTrains Tenderlight and Digital Interior Lighting.
4.4.23
Fixed a bug where a firmware update could lead to an invalid decoder configuration.
4.4.22
Fixed a bug that caused an invalid LokSound Select configuration when updating from 4.14.9202 or 4.14.9217.
4.4.21
Added new RailComPlus locomotive icons (for Mobile Control II).
Fixed firmware version of LokPilot V3.0 FX.
Fixed LokPilot V3.0 RailCom settings.
Added locomotive address to overview sheet.
Fixed "Decoder version n/a is not supported" error.
Automatic project type conversion to target decoder. (Can be disabled at Program settings -> Automatic decoder type conversion).
Added support for Scale Trains Tender Light.
Added support for Club car WGye.
Added support for LokPilot Standard Nano V1.0

[Gianfranco Lo Coco]

Ti conviene comunque aggiornare sempre i firmware dei decoder che molte volte migliorano il funzionamento e implementano le funzioni

[Frecciarossa]

Grazie Gianfranco!
Una curiosità: quindi se aggiorno non sono più supportati i ganci elettromagnetici della Roco, giusto?

[Gianfranco Lo Coco]

Esatto ma li puoi sempre utilizzare , utilizzando le uscite del decoder temporizzandole .

[alpiliguri]

Perché non sono supportati?
Secondo me: Output mode Roco coupler was missing on LokPilot V4.0 DCC.
vuol dire che si erano dimenticati di inserire questa modalità nei firmware precedenti, ma la 4.5.1 ha posto rimedio.
Ciao, alpiliguri.